Presentation is loading. Please wait.

Presentation is loading. Please wait.

Double Seal Plan - 52 Tandem Seal이라고 함.

Similar presentations


Presentation on theme: "Double Seal Plan - 52 Tandem Seal이라고 함."— Presentation transcript:

1 Double Seal Plan - 52 Tandem Seal이라고 함.
외부로부터 압력 Source가 없는 것으로 Buffer Fluid 는 Mechanical Seal에 설치된 Internal Pumping Ring에 의해 순환됨. Seal 유체가 대리로 유출될 때 위험성이 큰 경우에 사용. High Vapor Pressure Fluid, Light HC, Hazardous or Toxic Fluid *Connection / Consumption - Cooling Water - Pressure Switch Signal to DCS - Level Switch High Signal to DCS - Level Switch Low Signal to DCS

2 Double Seal Plan – 53A 외부 압력에 의해 Reservoir에 압력이 가함.(Double Seal)
대기로 Process Fluid가 Leak 되지 않아야 할 경우 High Vapor Pressure Fluid, Light HC, Hazardous or Toxic Fluid Reservoir의 압력은 최대 14 Kg/cm2.g 임 *Connection / Consumption - Cooling Water - Pressure Source (N2, Air etc) - Pressure Switch High Signal to DCS - Level Switch High Signal to DCS - Level Switch Low Signal to DCS

3 Double Seal Plan – 53B Plan-53A와 같이 외부압력을 가함.
Bladder Accumulator로 Gas를 축적함. Finned Pipe를 사용하여 유체를 냉각시킴. Plan-53A보다 높은 압력을 사용함. High Vapor Pressure Fluid, Light HC, Hazardous or Toxic Fluid Seal 유체의 압력이 떨어졌을 경우에 Manual Filling을 해줌. *Connection / Consumption - Pressure Switch Low Signal to DCS - Level Switch High Signal to DCS - Level Switch Low Signal to DCS

4 Double Seal Plan – 53C Plan-53A와 같이 외부압력을 가함. Plan-53A보다 높은 압력을 사용함.
Piston Accumulator를 이용하여 System Pressure의 Dynamic Tracking이 가능함. High Vapor Pressure Fluid, Light HC, Hazardous or Toxic Fluid Seal 유체의 압력상승에 의한 압력해소를 53B에서는 Buffer Tank로 한것과 달리 PSV가 그 기능을 함. 압력이 낮아졌을 시에 Manual Filling을 해줌. *Connection / Consumption - Cooling Water - Pressure Switch Low Signal to DCS - Level Switch Low Signal to DCS

5 Double Seal Plan - 54 외부 압력 Source는 있으나 Reservior가 없음.
High Vapor Pressure Fluid, Light HC, Hazardous or Toxic Fluid *Connection / Consumption - External Circulation Source

6 Quench Seals Seal Face에서의 Coking 또는 Crystallization을 방지하기 위해서 Water, Steam, Nitrogen 등을 사용하여 Quenching을 하여줌. Seal Plans – 62,65

7 Quench Seal Plan - 62 외부를 따라 냉각 가열 혹은 누설 액의 세정 등의 목적으로 Gas, Steam, Water 등을 Quenching하는 방법임 Seal 유체의 초기 조건에 따라 Quenching을 목적으로 하는 경우에 사용하는 방법으로서 Seal 유체가 100℃이상의 경우에는 Water Quenching을 피해야 한다. *Connection / Consumption - Quenching Source

8 Quench Seal Plan - 65 Plan-62의 Drain 측의 Leakage를 감지할 수 있게 추가기기를 설치한 것임. Process Leakage 또는 Quench Fluid의 Leakage를 감지할 수 있음. Plane-65만 사용하거나 Plan-65와 같이 사용하기도 함. *Connection / Consumption - Level Switch High Signal to DCS

9 Gas Seals Double Seal에서와 마찬가지로 Secondary Sealing을 함에 있어 Gas를 사용.
Seal Plans – 72,74,75,76

10 Gas Seal Plan - 72 가압되지 않는 상태의 Gas 압력에 의하여 Sealing이 됨.
Tandem Seal과 같은 개념 Plan-75 또는 Plan-76과 겸하여 Vent 과 Drain System을 사용한다. Vent 나 Drain은 보통 Low Pressure Vapor Recovery System이나 Flare와 연결됨. *Connection / Consumption - Sealing Gas Source - Pressure Switch Low Signal to DCS - Flow Switch High Signal to DCS

11 Gas Seal Plan - 74 Pressurized Barrier Gas Control System
가압 유체는 Nitrogen을 보통 사용 Double Seal 과 같은 개념. Barrier Gas는 Seal Chamber의 압력보다 최소한 1.5kg/cm2는 높아야 함. *Connection / Consumption - Sealing Gas Source - Pressure Switch Low Signal to DCS - Flow Switch High Signal to DCS

12 Gas Seal Plan - 75 Gas Seal의 Drain중에서 Vapor를 회수하기 위해 설치.
Vent Gas는 Low Pressure Vapor Recovery System 이나 Flare로 보냄. *Connection / Consumption - Pressure Switch High Signal to DCS - Level Switch High Signal to DCS

13 Gas Seal Plan - 76 Seal Vapor의 회수를 목적으로 사용
단독으로 사용되거나 Plan-72의 Vent System 으로 사용 대기온도에서 condensing이 되지 않는 유체에 사용 Vent되는 것은 Low Pressure Vapor Recovery / Flare system으로 보냄. *Connection / Consumption - Pressure Switch High Signal to DCS

14 Mechanical Seal의 적용

15 Mechanical Seal의 적용(예)
1) Single Seal 180℃ 미만: Use Plan 11 180℃ 이상: Use Plan 21 or Plan 23 Exceptions: - Water Pump : Use Plan23 above 80 ℃ - Hi-temp bellow Seal : Use Plan 11 2) Tandem Seal 180℃ 미만: Use Plan 11/52 180℃ 이상: Use Plan 21/52 or Plan 23/52 - Hi-temp bellow use seal plan 11/52

16 Mechanical Seal Selection
Pump Fluid Temp. (℃) Press. (kg/cm2g) Spec. Selected Plan G-GA104A/B ( ) HC+Solvent 38 Suc:0.275 Disch:3.09 V.P:1.083 12+52 G-GA106A 120 Suc:0.9 Dis:2.1 V.P:1.133 22+52 G-GA306A/B ( A-14) Butadiene 42.5 Suc:3.99 Dis:5.81 V.P:4.783 G-GA701A/B ( ) Solvent(DMF) Suc:-0.063 Dis:11.1 V.P:0.012 32+52

17 Mechanical Seal Selection
Pump Fluid Temp. (℃) Press. (kg/cm2g) Spec. Selected Plan G-GA706A/B ( ) Steam Condensate 85 Suc:0.21 Dis:5.01 V.P:0.795 22 G-GA501A/B (JA1-G ) Mixed C4 40 Suc:3.5 Dis:10 V.P:4.5 Vertical 13+52 U-GA105C (F7222U-5C) Ethylene -31.7 Suc:17.8 Dis:35.8 V.P:18.8 53C+61 C-GA703C (JA0-C ) Water 32 Suc:-0.42 Dis:5.05 V.P:0.05 12

18 Non-Seal Pump Canned Motor Pump의 장점 1) 축에 씰이 없으므로 해서 - 고압력,고온도,저온도,저융점
등의 액 취급에 적합함. 2) 취급액이 외부에 누출될 우려 가 없으므로 - 인체에 유해한 액 - 폭발성이 있는 액 - 인화성인 액 - 고가인 액 - 부식성이 있는 액에 취급이 용 Canned Motor Pump

19 Non-Seal Pump(계속) 3) 모터축이 펌프축을 겸하고있음으로 - 소형 경량이고 - 설치장소가 적음.
5) 외기를 흡입하지 않음으로 - 진공계의 운전 - 외기에 소이면 변하는 액 등의 취급에 적합. 4) 윤활유가 필요하지 않음으로 - 취급액의 오염이 없고 - 급유하는 수고가 필요없음. 6) 모터냉각용 Fan이 없음으로 - 운전송음이 없어 매우 조용함.

20 Non-Seal Pump(계속) Magnetic Pump
- 강력한 마그네틱 Coupling이 회전하면서 Impeller를 구동하는 방식. - 축이 완전히 밀봉되어있어 액의 누수가 없음. - 효율이 높아 운전시 전력소모가 적으며, 축봉장치가 필요없어서 Sealing Source공급및 교체등의 유지보수비가 절감된다.

21 질의 및 응답


Download ppt "Double Seal Plan - 52 Tandem Seal이라고 함."

Similar presentations


Ads by Google